Catskill-craftsmen 64228 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Nábytek Catskill-craftsmen 64228. Catskill Craftsmen 64228 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 16
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
CRAFTSMEN, INC.
Assembly Instructions
Model 64220/64228
Model 64220/64228
A. These units are Ready-To-Assemble. Catskill uses positive fastening methods such as wood
screws and in some places hidden Bastion Fasteners. You will need some standard household
tools: hammer and screwdriver. A power screwdriver is recommended. Where possible, we have
packaged some of the screws in separate labeled packages. To keep hardware separate after
packets are open, we suggest you place each type of screw into separate containers. Note labels
for screws and when they are to be used in assembly in the instructions.
B. Directions (left/right, front/back) are given as facing the front of an assembled upright unit.
C. A friend is recommended to assist with assembly as this will ease the process. Some of the
parts are large and awkward to hold in place, an extra pair of hands will help.
Model 64228 has Drop Leaf
Basic assembly is the same for both models with additional instructions for the drop leaf.
Zobrazit stránku 0
1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Model 64220/64228

CRAFTSMEN, INC.Assembly Instructions Model 64220/64228Model 64220/64228A. These units are Ready-To-Assemble. Catskill uses positive fastening methods

Strany 2 - Model 64220

STEP 9A. Stick magnet to magnet plate on a door.B. With all other doors open, close the door. The magnet should be positioned over the wooden block on

Strany 3 - These Parts in Model 64228

STEP 11A. Upright unit.B. Determine if you want the Knife Rack on the left or right Side Panel. The Handle/Towel Bar will go on the other. Then attach

Strany 4 - Hardware for 64228

STEP 13A. Tap 1” pins into the 4 sets of holes in the Back Panel. B. Just above the Bottom shelf on the inside of the Bottom Front Brace there are two

Strany 5

STEP 14 ONLY 64228A. Assemble top by placing the top and the drop leaf upside down on a smooth flat surface. Install hinges using 5/8 #8 screws. The l

Strany 6 - Model 64220 Model 64228

STEP 15A. Slide the Drawer into the front of the cart. B. Tap in the 5/8 wooden plugs into the holes on the legs.C. Install Small Middle and Center Sh

Strany 7 - 5/8” #6 Screw

For continued beauty and long life of your Catskill Craftsmen cart, we recommend Catskill Craftsmen’s Butcher Block Oil. If you would like to purch

Strany 8

WRONG!Post needs to be screwed deeper.WRONG!Post needs to be backed out.CORRECT!Set screw secures post properly.Step 1 1. The Bastion fastening syste

Strany 9 - 1” Pins1” Pins

Parts List Model 64220Drawer Bottom (1)P/N DBOT-64220/28Small Middle Shelf (2)P/N SMS-64220/28Center Shelf (1)P/N CS-64220/28Bottom Shelf (1)P/N BS-64

Strany 10 - No pilot holes as softwood

Side Panel (2)P/N SP/HDL-64220/28 Divider Panel (2)P/N DP-64220/28Back Panel (1)P/N BP-64220P/N BP-64228Glide Support (2)P/N GLDSUP-64220/28Knife Rack

Strany 11

Hardware for 642201 3/4” Phillips Flat Head Bolt (8) 1 1/4” Phillips Flat Head #8 Screw (18) 1” Truss Head Machine Screw (12) 5/8” Pan Head Screw (8)

Strany 12 - STEP 14 ONLY 64220

A. Tap/insert ONE 1 1/2” pin into each end of all the doors. DON’T OVERDRIVE PINS! Pins should stick up about 1/2” when seated.B. Attach the magnet pl

Strany 13 - STEP 14 ONLY 64228

STEP 3A. Assemble Knife Rack by inserting four brass colored 1 1/4” #8 Screws through the countersunk (reamed out) holes in the Knife Rack into the pi

Strany 14

STEP 5ILLUSTRATION 5A. Attach a Glide Support Stick to the top of each Side Panel using 1 1/4” #8 screws. The countersunk holes (reamed out) in the st

Strany 15 - BUTCHER BLOCK OIL COUPON

STEP 6A. Lay Back Panel flat on a smooth surface with holes up.B. Attach Side Panels with 1 3/4” machine screws (bolts) and hex nuts. After inserting

Strany 16 - See video on our website!

STEP 8A. Install Doors by fitting the pins in the top of the door into the holes in the Top Front Brace. B. Place washers on the pins on the bottom of

Příbuzné modely 64220

Komentáře k této Příručce

Žádné komentáře